Øgelundgård
Big Brother in the dairy barn: Every mouthful is measured
At Søren Røndbjerg’s farm, near Give in Denmark, cameras monitor how much each cow eats and how much it weighs. The aim is to improve breeding, make feeding more precise and reduce the carbon footprint per kilogram of milk.
You hardly notice them as you walk through the barn at Søren Røndbjerg’s farm. But 4.2 metres above the cows, 180 white cameras are mounted, keeping track of how much each individual cow eats.
There is something rather Big Brother-like about it, but the cows are completely unaware of the surveillance, and the white boxes almost blend into the barn. Søren Røndbjerg explains how they work as he walks among his 350 dairy cows.
The cameras are intended to provide both him and Viking Genetics with valuable new information. By combining data on feed intake and body weight with milk yield, it becomes possible to identify the cows that convert feed into milk most efficiently.
This knowledge can be used in breeding programmes, but it also gives Søren Røndbjerg a better basis for managing his herd on a daily basis.
The aim is to breed cows that produce more milk from less feed. This could reduce the carbon footprint in two ways: by lowering methane emissions from the cows’ digestive systems and by reducing emissions associated with feed production, as less feed would need to be grown to produce the same amount of milk.
Both effects could reduce greenhouse gas emissions, measured in CO₂ equivalents, per cow and per kilogram of milk. The size of the benefit depends, among other things, on the composition of the feed ration.
A picture every five seconds
It may seem difficult to understand how cameras in a barn can provide such detailed information, but the principle is relatively simple.
The cameras take a picture every five seconds. When a cow is eating, the system measures the size of the feed pile before and after. An algorithm then calculates how much feed the cow has consumed based on the difference.
After milking, the cows walk one at a time through the return passage. Here, they are identified by the electronic chip in their ear tag, while another camera scans their backs and calculates their body weight.
This is considerably simpler than weighing the cows on a conventional scale equipped with load cells. It is also more reliable, as there are fewer mechanical components that can break down.
Søren Røndbjerg has compared the camera measurements with weights recorded at the slaughterhouse. The difference was just nine kilograms for a cow weighing approximately 750 kilograms.
“It is remarkably accurate,” he says.
When feed intake, body weight and milk production data are combined, Viking Genetics can calculate how efficiently each cow converts feed into milk.
The results can then be traced back to the cow’s sire, and the information is incorporated into the bull’s breeding index.
It is an efficient way of collecting large numbers of observations, and the more observations available, the more reliable the breeding values become.
Faster decisions
Although the cameras were primarily installed to support breeding work, Søren Røndbjerg can also use the data in his daily herd management.
The figures are transferred to the DMS herd management system on his computer. Here, he monitors whether the cows are gaining or losing weight and whether they are following their expected weight curves.
He can examine the figures for individual cows or for entire groups.
This is particularly useful when he makes changes to the feeding programme. If the cows start losing weight, he can increase the energy level of the ration. If they gain too much weight, he can adjust it in the opposite direction.
“Previously, we looked at these things more generally over a longer period. Now I can respond much faster. I cannot tell with the naked eye if a cow has lost 600 grams, but we can detect that with the cameras,” he says.
What has surprised him most is how quickly changes in feeding become visible in the data.
The dry cows also provide useful information, even though there are no cameras monitoring their feed intake. They are weighed when they leave the milking herd and again when they return.
“I can see whether they have lost or gained weight during the dry period. Then we can adjust the feeding level if necessary,” he explains.
Breeding from the best
Viking Genetics has paid for the cameras as part of its efforts to make its breeding programme more efficient. More specifically, the aim is to improve breeding indices for feed intake and feed efficiency.
This will enable the company to identify and promote bulls with favourable genetics more quickly and accurately, while selecting against those with less desirable traits.
In the longer term, this should benefit all dairy farmers who purchase semen from Viking Genetics.
On his own farm, Søren Røndbjerg can use the same information to select the cows he wants to breed from.
“I identify the best cows and get rid of the worst. Last year, I produced 166 embryo-transfer calves using embryos from my best cows,” he says.
He also sees opportunities for further development.
Viking Genetics is working on using images of cows’ backs to detect lameness based on the curvature of the spine.
The technology is not yet ready for practical use, but Søren Røndbjerg hopes that one day it will be able to send an alert through DMS, allowing him to identify and treat lame cows at an earlier stage.
Spiders get in the way
Søren Røndbjerg does not pay for the cameras themselves, but he does pay for the electricity they consume. The original agreement with Viking ran for four years and has since been extended.
“Potentially, there is an enormous amount of money to be gained from this for dairy farmers as a whole. But with electricity being so expensive, quite a few farmers with cameras are grumbling about their electricity bills,” he says.
Fortunately, keeping the system running requires very little effort on his part.
Viking Genetics receives the data remotely and is responsible for servicing the equipment. Most of the time, the system looks after itself.
“Occasionally, they call and ask me to switch the power off and back on again. Other times, I have to remove a spider that is blocking the view from a particular camera,” he says, pointing upwards.
Søren Røndbjerg sees enormous potential in cameras and other technologies that provide farmers with more precise information about their cows.
However, he also believes that farmers need to learn how to sort through the growing volumes of information.
“We are getting more and more data. In the past, we relied much more on guesswork. Now the information appears on the screen. The challenge is to use the most important information, because you cannot use all of it,” he says.
Øgelundgaard
• 350 Danish Red (RDM) dairy cows
• 11,800 kg of energy-corrected milk (ECM)
• 350 hectares
• 182 cameras
• Currently expanding the dairy facilities to accommodate more cows and milking robots
Six milking robots will make room and time for more cows
Søren Røndbjerg is building a new dairy barn with six milking robots and space for 460 cows. The investment is intended to reduce the workload and ensure that the facilities meet the requirements coming into force in 2034.
The foundations have been excavated, and machinery is busy levelling the ground. Soon, a new dairy barn will rise at Øgelundgaard, where buildings from different periods tell the story of the farm’s development.
The most significant change will be the installation of six new Lely milking robots.
They will replace the existing milking parlour and enable Søren Røndbjerg to expand his herd from 350 to 460 cows without hiring additional employees.
“We expect to manage another 100 cows with the same number of employees,” he says.
A different working day
A great deal of preparation has gone into the decision. Søren Røndbjerg has visited robotic milking facilities abroad and discussed experiences with fellow dairy farmers.
“The new generation of milking robots is in a completely different league from the old ones. They actually work now,” he says.
Working conditions have also played an important role in his decision.
Søren Røndbjerg believes that a more flexible working day, with less manual labour, will make it easier to attract employees.
“It will be easier to recruit Danish employees when you have a system like this,” he says.
The robots will take over the milking, but they will not eliminate the need for staff.
Instead, employees will have to use the information provided by the robots and monitor cows that need extra attention.
“You no longer handle the udder yourself every day. Instead, you receive information from the robot and have to respond to it,” he explains.
He also hopes that the robots will allow more milkings per cow and lead to higher milk yields.
Additional space and water-filled mattresses in the cubicles will provide better conditions for the cows.
Ready for 2034
The new barn will have three rows of cubicles on each side of a central feed passage, with three milking robots on either side.
A deep-bedded area will accommodate cows that need extra attention or a quiet place to recover. There will also be facilities for separating cows for insemination.
At the same time, the barn is being designed to comply with the housing requirements that take effect in 2034.
Staff facilities, including a changing room and showers, will also be provided, while the overall layout is intended to make daily work easier and less labour-intensive.
Room for the next step
Even before the new barn is completed in the coming months, Søren Røndbjerg has already made provisions for another expansion.
A second barn could eventually bring the herd to around 950 cows.
It would also be less expensive to construct because technical rooms and staff facilities could serve several barns.
But the investment is also about the next generation.
Søren Røndbjerg’s father is in his seventies and still works on the farm. Søren himself, who is just under 50, feels far too young to retire, while his two daughters are attending agricultural college.
These family considerations have played a part in his decision to invest rather than allow the existing buildings to gradually wear out.
“They should only take over if they want to. But if they do want to take over, there will be something worth taking over. Otherwise, I could simply let the place run down,” he says.
Related content
- Download and access the article above as Word document: Big Brother in the dairy barn